Rheem 3 Ton Variable Speed Air Handler

 RH1V/RH2V- Series

• Quiet, efficient ECM motor technology providing nominal airflow up to 1.0 inch [25 kPa] of external static pressure.
• Interface board with dip switches conveniently located in the blower compartment allows for precise, field selectable airflow to meet the requirements of particular applications.
• Selectable continuous fan "on" options.
• The most compact unit design available.
• Attractive pre-painted cabinet exterior.
• Rugged steel cabinet construction, designed for added strength and versatility.
• 1.0" foil faced insulation mechanically retained in blower compartment.
• Four leg rubber insulated motor mount.
• Field-installed auxiliary heater kit includes circuit breakers that meet UL and cUL requirements as a service disconnect switch.
• Blower housing with integrated controls, motor and blower. Slide out design for service and maintenance convenience.
• Field convertible for vertical upflow, vertical downflow, horizontal left hand or right hand air supply.
• Combustible floor base accessory available when required for downflow installations on combustible floors.
• Indoor coil design provides low air side pressure drop, high performance and extremely compact size. All coils come with PVC condensate elbow standard.
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing.
• Coils are tested at the factory with an extensive refrigerant leak check.
• Coils have copper sweat refrigerant connections.
• Coils utilize chatleff metering device connections.
• Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils.
• Supply duct flanges provided as standard on air handler cabinet.
• Provisions for field electrical connections available from either side or top of the air handler cabinet.
• Connection point for high voltage wiring is inside the air handler cabinet. Low voltage connection is made on the outside of the air handler cabinet.
• Concentric knockouts are provided for power connection to cabinet. Installer may pull desired hole size up to 2 inches (51 mm) for 1 1/2 inch (38 mm) conduit. Front refrigerant and drain connections.

• Standard Features:
   

  • Quiet, efficient ECM motor technology providing nominal airflow up to 1.0 inch [25 kPa] of external static pressure.
  • Interface board with dip switches conveniently located in the blower compartment allows for precise, field selectable air-flow to meet the requirements of particular applications.
  • Selectable continuous fan on options.
  • The most compact unit design available.
  • Attractive pre-painted cabinet exterior.
  • Rugged steel cabinet construction, designed for added strength and versatility.
  • 1.0 foil faced insulation mechanically retained in blower compartment.
  • Four leg rubber insulated motor mount.
  • Field-installed auxiliary heater kit includes circuit breakers that meet UL and cUL requirements as a service disconnect switch.
  • Blower housing with integrated controls, motor and blower.
  • Slide out design for service and maintenance convenience.
  • Field convertible for vertical upflow, vertical downflow, horizontal left hand or right-hand air supply.
  • Combustible floor base accessory available when required for downflow installations on combustible floors.
  • Indoor coil design provides low air side pressure drop, high-performance and extremely compact size. All coils come withPVC condensate elbow standard

  
  Cabinet Features:
   

  • Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing.
  • Coils are tested at the factory with an extensive refrigerant leak check.
  • Coils have copper sweat refrigerant connections.
  • Coils utilize chatleff metering device connections.
  • Molded polymer corrosion resistant condensate drain pan is provided on all indoor coils.
  • Supply duct flanges provided as standard on air handler cabinet.
  • Provisions for field electrical connections available from either side or top of the air handler cabinet.
  • Connection point for high voltage wiring is inside the air handler cabinet.
  • Low voltage connection is made on the outside of the air handler cabinet.
  • Concentric knockouts are provided for power connection to cabinet.
  • Installer may pull desired hole size up to 2 inches, 51 mm, for 1 1/2 inch, 38 mm conduit.
  • Front refrigerant and drain connections.

• Wiring Diagrams
   
• Parts List
   
• Installation Instructions
   
• Specification Sheet